Mounting Dream UL Listed Full Motion Monitor Wall Mount TV Bracket for 10-26 Inch LED, LCD Flat Screen TV and Monitor, TV Mount with Swivel Articulating Arm, Up to VESA 100x100mm and 33LBS MD2463

I was looking for a monitor stand and ended up getting a triple monitor desk stand that didn’t work out too well. I ordered three of these wall mounted stands because I was a little frustrated with the other product and how it wobble when I had it on my desk. These mounts were very easy to install and the instructions are very straight forward. The package comes with a nice level that can be used to make sure the mount is installed nicely.The product says the mount will hold monitors up to 26″ but I ended up using a 27″ Philips monitor and two 24″ Philips monitors. The mounts hold all monitors fine. The package arrived overnight and I had absolutely no problems setting the mounts up from start to finish.If you are looking for wall mounted monitors I would definitely recommend this brand. I even bought a TV wall mount of the same brand and loved that mount as well.I also believe the price point of these mounts are very reasonable. Purchasing three of these mounts was still less than the single triple monitor stand I purchased and these work a lot better. I’ve had these mounts for about two weeks now and have had absolutely no complains whatsoever.I really don’t have any negative words to say.

This mount is very sturdy and its a quality product for sure. I wanted to save desk space for my gaming and amateur streaming setup, and this worked perfectly as you can see in the photos! Easy to mount and holds my 21 inch secondary monitor with no worries, and it will hold a larger tv or monitor as well, but anyways it has great range of motion and easy to assemble. Just disconnect the tv/monitor bracket aka the vesa mount from the mount arm (only two bolts easy) and attach it to your monitor or smart tv, using the four screws with washers, whichever best fit your tv/monitor (it comes three sets of different sizes of screws to attach the vesa mount to your tv/monitor easy) make sure your tv or monitor is the specific vesa mount size that fits this particular mount, btw. Then there is only three main lag bolts to secure the mount to the wall, very easy to do and it comes with a stencil to mark your three drill points for the mount to attach to the wall. Only three holes to drill with a 1/8 drill bit or you probably could get away with just using a hammer and small nail to get three starter holes for the three lag bolts and bam! Then you just grab your monitor or tv with the vesa mount attached to it and hang it onto the mount arm and use the two bolts that you originally disconnected the vesa mount from the arm and tighten them back down and viola your goal is accomplished! Dang it Bobby, now your ready for some dang vidya games or streaming or just watching tv if you like, GG’s everybody!

This was a fantastic mount. The unit is built very well and had the best price!

We installed this wall mount in 5 mins of that. Very sturdy I love that it swivels.

If you’re contemplating a $100 mount to hold your small-ish TV, put down the $100 mount and think again. (I actually took my $100 mount back to Best Buy without even opening it. You see, I didn’t put it down in time. Don’t be like me.)This mount is absolutely perfect for a 24″ Vizio that cost around $170. Why pay nearly 2/3 the TV price for a mount? Crazy.The maximum hole spacing on this mount is 100mm which is ideal for a lot of small TVs. You could get a bigger mount for a possible TV upgrade down the road, but the bigger mounting plate might interfere with inputs on the back of the TV. Keep it simple with this small mount. And if you ever upgrade to a bigger TV, just upgrade the mount right along with it. From the perspective of weight, this could hold a much bigger TV. The only issue would be the hole layout on the bigger TV.This comes with everything you need and more. It includes several different screw sizes to accommodate common hole sizes on TVs, and it includes both lag bolts for installation into a stud, and anchors for installation into concrete. It also includes a wrench, but the wrench isn’t used for installation (I believe it’s only intended for tightening the bolt for the tilt). For installation into a stud you’ll need a drill with 1/8″ drill bit, a screw driver, and an adjustable wrench or socket set for turning the lag bolt. I think the lag bolt size is metric. I didn’t have a socket that fit it, so I used the adjustable wrench with no problem. Most people can install this without instructions, but they’re worth looking at to make sure you use the included washers/spacers when necessary.Our 24″ Vizio TV is only 6.8 pounds so it’s on the very low end of what this mount can hold. Ideally, this mount would extend straight from the wall a couple more inches, but I understand with larger, heavier TVs a longer arm poses a structural problem. Anyway, this is installed on the wall of the top bunk of a bunk bed, and the TV can be rotated a full 90-degrees (so it’s perpendicular to the wall) without coming into contact with the wall. There’s an inch or two gap which is good, but it doesn’t leave a lot of wiggle room. On bigger TVs this would be an impossible configuration given the arm extension length of this mount. Just keep this in mind if your application is for the TV to be perpendicular to the wall most of the time.Overall I have to say this is a great mount and I couldn’t ask for more given the price.UPDATE 1/25/16 (Original review 1/22/16): The advertised 360-degree rotation of the mounting plate cannot be tightened/fixed with the bolt through the mounting plate. That bolt only tightens/fixes the tilt position. So even with a fixed tilt position the mounting plate will rotate 360-degrees. This is a slight annoyance, but not enough to change my original review score, especially considering price. Just FYI in case you’re looking to be able to lock the TV into a certain position axially around the bolt.